Альтернативные Методы Для Цветного Fine Art-а |
Здравствуйте, гость ( Вход | Регистрация )
Альтернативные Методы Для Цветного Fine Art-а |
8.12.2011, 14:51
Сообщение
#1
|
|
Активный участник Группа: Пользователи Сообщений: 36 Регистрация: 7.12.2011 Из: Екатеринбург Пользователь №: 46377 |
не знаю где спросить, поэтому спрошу здесь.
сам я в химии не силен и всегда пользовался готовыми наборами. все химиченье ограничивалось составлением простых проявителей, ну еще обращал ч/б. ездил я снимал пейзаж на 4x5 velvia 50 и печатал на илфохроме. получалось очхорошо, народ отпечатки покупал. НО нарисовалась проблема: илфорд собрался свернуть произовство илфохрома (надеюсь что все таки передумают). соответственно стал вопрос - а какая же альтернатива илфохрому имеется для fine art цветной фотографии? накопал Kodak Dye Transfer. который был снят с производства в 94-м, но опубликована вся рецептура: http://www.dyetransfer.org/images/DyeTran.pdf описание процесса здесь: http://www.charlescramer.com/dyetransfer.html но вся соль процесса в специальной пленке (в оригинале Kodak Pan Matrix Film 4150) при помощи которого происходит перенос красящего пигмента на бумагу. приводится вот такой рецепт эмульсии: The following formulation (Trial # 20) is for four Liters of emulsion: Solution A: Potassium Bromide 168 g Potassium Iodide (5% solution) 62.4 ml Inert Gelatin 160 g Distilled Water 3500 ml Solution B: Silver Nitrate 160 g Distilled Water 500ml Solution C: (for 500 ml of emulsion) Sodium Thiosulfate (0.1% solution) 1 ml Gelatin 30 g (Gelatin added directly to the heated emulsion) Solution D: (for 500 ml of emulsion) Potassium Bromide (1% solution) 10 ml Manganous Sulfate (1% solution) 10 ml 7-Hydroxy-5-Methyl-1, 3,4-triazaindolizine (1 % solution pH 7.2) 7.5 ml Acid Yellow Dye # 23 (Tartrazene) 1.5 g Triton X-200 (1% by volume) 3 ml Sorbitol 3.75 g Note: Adj. pH of triazaindolizine solution to 7.20 by adding Sodium Hydroxide. Solution E: (for 500 ml of emulsion) 1-Phenyl-5-Mercapto Tetrazol 0.1% in Ethanol 4 ml Sodium Azide 6.5% water solution 20 ml Emulsification / Physical Ripening Add B (at 55° C) to A (at 55° C). Use a burette over a heated beaker holding solution A at 55° C. Stir the solution using a paddle mixer. (Approx. 200 rpm). Temperature must be controlled to 1° C using a temperature controller and hot plate. Addition as follows: Add 10 ml of B to A in 5 seconds. Wait 1 minute Add 245 ml of B to A over 4 minutes. Wait 10 minutes Add 245 ml of B to A over 5 minutes. Ripen additional 15 minutes Immediately chill the emulsion using an ice bath. Chill until the emulsion is very solid, whack the side of the container, there should be a distinct ‘jiggle’ feeling. • Washing Cut the emulsion into ‘noodles’ 1/4” crossection. Wash using tap water for 4 hours. Change water frequently. The following steps prepare 500 ml of emulsion for coating one sheet. Note: To prepare a batch of film having matched speed, do the following steps on the full quantity needed. Multiply the quantities by as many sheets as you are going to coat. Sensitize the emulsion, and add the final prep. Filter the entire batch in two stages, first with 40 um filter paper, followed by 5 um filter paper. Use a vacuum filtration system. Pour the emulsion into 1L stainless containers with lids, 500 ml per container. Refrigerate until fully gelled. Remelt the emulsion in one of these containers, and immediately coat. Use the same procedure for each coating. • Sensitization (Digestion or Chemical Ripening) Remelt the emulsion, heat to 55° C. Add the 30-g gelatin to the mix, and stir until fully dissolved. Add Solution C, mix thoroughly. Stir for 70 minutes while maintaining temp at 60° C. Control temp to 1° C. Cover the vessel with aluminum foil while stirring to prevent fogging from the safelight. • Final Prep Add solution D, mix. The Tartrazene dye is used to absorb blue light to cause the depth penetration exposure effect and to minimize scattering. The Triazaindolizine is a stabilizer, and is available in bulk from Allied Signal Corp. 937-455-3005. A wetting agent Triton X-200 is added to promote even coating. Triton X-200 is an an-ionic surfactant. It is available from Union Carbide Corp. 1-800-568-4000. The Sorbitol is a plasticizer used to minimize reticulation, drying marks, and minimize curl. Mix a full batch of emulsion, and pour into separate containers. Before coating, or if not coating within one week, add solution E. This has a stabilizer which minimizes fogging in long term storage, and the Sodium Azide acts to preserve the emulsion when stored. Store chilled. • Coating Coat 500 ml over a 32” X 50” area. At > 100° F. If you use a dip coating technique where you can obtain thin coatings, you should coat a 7 um thickness (dry emulsion tickness). • Setting Set at 50° F for 10 minutes to gel emulsion. Note - the emulsion may reticulate at this point if it is too thick. 4 • Drying Dry in a dust free enclosure for 12 hours at room temperature. насколько сложно приготовить и полить это самому? и насколько получится предсказуемый результат. и второй вопрос - если посмотреть на проблему шире, то для получение хорошего цветного отпечатка нужно взять качественные пигменты (те же Acid Blue 45, Acid Red 80, Acid Yellow 11, которыем можно купить) и каким то образом перенести их на бумагу. весь кайф илфохрома да и кодахрома был как раз в правильных красителях, которые были заложены в илфохроме изначально (или которые вносились в кодахром в процессе проявки). есть ли какие то еще альтернативные процессы, для полутонового переноса красителя на бумагу. полиграф процессы не подойдут из-за отсутствия полутонов (необходимости растризации). просьба сильно не пинать за сумбурность мыслей. |
|
|
11.12.2011, 11:12
Сообщение
#2
|
|
Активный участник Группа: Пользователи Сообщений: 1188 Регистрация: 24.6.2010 Пользователь №: 5785 |
ага, а исчо галогенид серебра полупроводник с примеными акцепторами, знаем знаем,
ждем когда китайцы матрицу создадаут с пикселем соизмеримым с длинной волны -------------------- Прояви ! Сникерсни !
|
|
|
11.12.2011, 11:17
Сообщение
#3
|
|
Активный участник Группа: Пользователи Сообщений: 36 Регистрация: 7.12.2011 Из: Екатеринбург Пользователь №: 46377 |
> не надо мусорить русский язык англоязычными терминами, скажите непрерывный тон лучше.
sorry - это профтермин. continous tone - в переводе с англ. что то типа "непрерывные полутона". то есть есть кол-во полутонов стремиться к бесконечности в отличие от 256 в компьютерном 8-битном представлении. > ага, а исчо галогенид серебра полупроводник с примеными акцепторами, знаем знаем, > ждем когда китайцы матрицу создадаут с пикселем соизмеримым с длинной волны такого не слышал, но что то верится с трудом что кетайсы смогут . |
|
|
Текстовая версия | Сейчас: 29.4.2024, 0:00 |